Skip to main content
  • Research Article
  • Open access
  • Published:

Analysis of tilianin and acacetin in Agastache rugosa by high-performance liquid chromatography with ionic liquids-ultrasound based extraction

Abstract

Ionic liquid 1-butyl-3-methylimidazolium bromide-methanol-based ultrasonic-assisted extraction (ILUAE) was used to extract tilianin and acacetin from the aerial parts of Agastache rugose (A. rugose), and simultaneously determined by reversed phase high performance liquid chromatographic (RP-HPLC) method with ultraviolet detection (RP-HPLC-UV). An InertSustain RP-C18 column was used with the mobile phase consisting of methanol and 0.2% acetic acid as gradient elution at the detection wavelength of 332 nm. The flow rate was 0.8 mL/min, and the column temperature was 30 °C. Under the optimized conditions, tilianin and acacetin displayed good linearity in the ranges of 0.0595–4.76 and 0.0585–4.68 μg/mL, respectively, with the average recoveries being 96.93 and 97.88%, respectively. The method of ILUAE was compared with the traditional methods, it exhibited higher efficiency, higher reproducibility and environmental friendly in analyzing the active compounds in traditional Chinese medicines (TCMs).

Background

Agastache rugosa (Fisch. & C.A.Mey.) Kuntze (A. rugose), a medicinal plant belonging to the family Lamiaceae, is native to China, Korea, and Japan. A. rugosa shows the similar taste and thermal properties to those of pungent (acrid) and is slightly warm with the channel affiliations entering spleen, stomach and lung. It can dispel damp, and relieve nausea and vomiting, and cure fungal infections. Pharmacological investigations have shown that A. rugosa have antiviral [1], antimicrobial [2], antioxidant [3], cardiovascular and anti-inflammatory [4, 5] activities, and some other activities [6].

At present, there are still many problems during the process of development and utilization of TCM resource, including lower efficiency, higher energy consumption, higher pollution, longer production cycle, and waste of resources etc. The products of TCMs also have many shortcomings, for example, low yield, many impurities and poor quality etc [7]. Ionic liquid (IL) is a new substance which has been developed in the framework of green chemistry in the recent years. Ionic liquids (ILs) are the substances solely composed of anions and cations. The interests in the ILs have significantly increased because of their special properties. They are good solvents for both organic and inorganic liquids, over a wide range of temperatures, and are not volatile, highly negligible vapor pressure, thermally stable, nonflammable, polar, weakly coordinating solvents and less toxic than usual organic solvents [8, 9]. Using IL as a solvent to extract the active ingredients of TCM is not only environmental friendly, but also selective and also has high yield and pre-concentration [10]. Thus, the extraction of active ingredients of TCM by IL is a breakthrough method, because it provides reference for the healthy and sustainable development of TCM resources.

The conventional methods of extraction of natural products from plant materials are mainly by maceration, which is very time-consuming and requires relatively large quantities of toxic organic solvents [11]. Ultrasonic-assisted extraction (UAE) has been found to be a more effective and environmentally friendly way of extracting natural product from plant materials for its characteristics of shorter extraction time and use of less amounts of organic solvents. Several groups of investigators extracted the total flavonoids from corn silk by UAE and obtained a high extraction yield [1217]. Thus, in this study, we chose UAE to extract the target analytes from A. rugose.

In our previous chemical research, we isolated abundant tilianin and acacetin from A. rugosa. Our previous studies together with the other reports [4, 18] have indicated that tilianin and acacetin are the main active compounds. Thus, 1-butyl-3-methylimidazolium bromide-methanol solution was used as extraction agent in combination with high performance liquid chromatography (HPLC) simultaneous to separate and determine tilianin and acacetin. To our best knowledge, the simultaneous extraction of flavonoid and flavonoid glycosides in A. rugosa using IL has not been reported yet to date. The present study aimed to establish a rapid, greener and effective ionic liquid-based ultrasonic-assisted extraction method (ILUAE) for simultaneous extraction of tilianin and acacetin from A. rugosa.

Experimental methods

Chemicals and material

Methanol of chromatographic grade was purchased from Tianjin Da Mao Chemical Reagent Factory (Tianjin, China). The ultra pure water was purchased from Hangzhou Wahaha Baili Food Co. Ltd, (Zhejiang, China). Acetic acid was obtained from Tianjin Fu Chen Chemical Reagent Factory (Tianjin, China). 1-butyl-3-methyl imidazolium tetrafluoroborate ([BMIM]BF4), 1-butyl-3-methyl imidazole bromide ([BMIM]Br) and 1-butyl-3-methylimidazoliumhexafluorophosphate ([BMIM]PF6) were obtained from limited partnership Merck (Darmstadt, German). 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIM]PF6) was purchased from Thermo Fisher Scientific (Rockville, MD, USA).

A LC-20AT high performance liquid chromatography system (Shimadzu, Kyoto, Japan), equipped with a degasser, a quaternary gradient low pressure pump, the CTO-20A column oven, a SPD-M20AUV-detector, a SIL-20A auto sampler was used. Chromatographic separations of target analytes were performed on an InertSustain C18 column (4.6 mm × 250 mm, 5 µm). KQ-500DB ultrasonic cleaner (Jiangsu Kunshan Ultrasonic Instrument Co., Ltd. Jiangsu, China); FZ102 micro plant sample pulverizer was obtained from Huanghua, Hebei Zhongxing Instrument Co., Ltd. (Baoding, Hebei, China); sample sieves were obtained from Sieve Factory (Five Four instrument, Shangyu, Zhejiang, China); AB135-S 1/10 million electronic balance was purchased from Mettler Toledo Instruments Co., Ltd. (Shanghai, China).

Plant material and sample preparation

Agastache rugosa (Fisch. & C.A.Mey.) Kuntze (A. rugose) was collected in October 2013 from the Suzhou region of Jiangsu Province, China and identified by a plant scientist, Professor Changqin Li. A voucher specimen (201310231) was deposited in the Institute of Traditional Chinese Medicine, Henan University. The plants were dried in shade at room temperature, the dried plants material were pulverized and then passed successively through 90, 70, 50, 24 and 10-mesh sieves.

For sample solution, 50 mg of A. rugosa powder was passed through 50-mesh sieve, and put in 1.5 mL centrifuge tube. 1 mL of the extraction solution was added, followed by ultrasonic extraction for 30 min to obtain supernatant. The supernatant was passed through a 0.22 μm organic microporous membrane. The filtrate was obtained and used as the sample solution.

For standard sample solution, 1.17 mg of acacetin and 1.19 mg of tilianin were dissolved in methanol in 25 mL volumetric flask to yield the stock solutions. The concentrations were 0.0468 and 0.0476 mg/mL, respectively.

Ionic liquids-based ultrasonic-assisted extraction

The preparation steps of ILs methanol solutions were as follows (0.8 M): certain amounts of different ionic liquids (according to their molar masses) were accurately weighed, fully dissolved in methanol and then diluted to 1 mL with methanol in a volumetric flask (1 mL), respectively. 50 mg of dried sample powder was mixed well with 1 mL of IL-methanol solution in a 1.5 mL centrifuge tube. The centrifuge tube was then most partially immersed into the ultrasonic water bath. The temperature of water bath was controlled by the replacement between inlet and outlet water. The bath power rating was 100 W. At room temperature (20 °C), after ultrasonic extraction, the contents of tilianin and acacetin were determined by reversed phase high performance liquid chromatographic-ultraviolet (RP-HPLC-UV). The type of ILs, the concentration of selected IL, the mesh sieve through which of A. rugosa was passed, the ultrasonic time and solid–liquid ratio were systematically investigated in this experiment.

Chromatographic conditions

Chromatographic conditions were set as follows: separation column, InertSustain C18 column (4.6 mm × 250 mm, 5 μm); mobile phase, methanol (B)-0.2% aceticacid (C), gradient elution (0–10 min, 40–55%B, 60–45%C; 10–20 min, 55–65%B, 45–35%C; 20–30 min, 65–75%B, 35–25%C; 30–40 min, 75–80%B, 25–20%C; 40–50 min, 80–100%B, 20–0%C; 50–70 min, 100%B), column temperature, 30 °C; flow rate, 0.8 mL/min; the UV detection wavelength, 332 nm; and sample volume, 10 μL.

Results and discussion

The selection of the wavelength

Xie et al. [19] found that the optimum wavelength of acacetin was 332 nm with DAD detector scanning. The optimum wavelength of tilianin was mostly selected at 330 nm [20, 21]. In the experiment, the 332 nm was selected as the detection wavelength because we found that there was less interference at this wavelength.

Selection of dispersing agent

At room temperature, IL is a liquid with high-viscosity (usually higher than that of the conventional organic solvent by 1–3 orders of magnitude). Because [BMIM]Br is crystalline, we need a suitable solvent to dissolve the IL. During the course of the study, we found that [HMIM]PF6 and [BMIM]PF6 were water insoluble. The extraction rates of IL-ethanol and IL-acetonitrile were lower than that of IL-methanol, while acetonitrile had a higher toxicity. Thus, methanol was chosen as the dispersing agent.

Linear relationship

For preparing standard sample solutions, various amounts of tilianin and acacetin were dissolved in methanol to yield the stock solutions, respectively. Corresponding calibration curves for tilianin and acacetin were Y = 1336560814x + 17243, (r = 0.9999) and Y = 5785424072x + 27367, (r = 0.9999), respectively. Both tilianin and acacetin displayed good linearity in the ranges of 0.0595–4.76 μg/mL and 0.0585–4.69 μg/mL, respectively. The limit of detection (LOD) and the limit of quantification (LOQ) of tilianin were 1.59 and 2.18 ng/mL, respectively while LOD and LOQ of acacetin were 0.1081 and 0.225 ng/mL, respectively.

Optimization of extraction conditions

Type of the ILs determination

The structure of ILs had significant influence on their physicochemical properties, which might greatly affect the extraction yields of target analytes [22]. In this experiment, [BMIM]BF4, [BMIM]Br, [BMIM]PF6, and [HMIM]PF6 ILs-methanol were selected as extraction solutions to measure the contents of tilianin and acacetin. The results were shown in Fig. 1. In Fig. 1, the extraction yields of 4 kinds of ILs-methanol solution were higher than that of MeOH. Among these ILs-methanol solutions tested, the extraction yield of [BMIM]Br-methanol was the highest one. Thus, the [BMIM]Br-methanol was chosen as the extraction solution. Ha et al. reported that many ILs showed high capacity for cellulose dissolution, especially halide and phosphate anions [23]. The primary cell wall of medicinal plants is made primarily of cellulose. The ILs mainly action cell wall components, dissolve them in turn, increase the cell wall permeability, resulting in higher yield of the effective constituents [24]. In addition, IL had a good ability to dissolve inorganic and organic matters. The solubility of tilianin and acacetin were not good, and ILs had a good ability to dissolve tilianin and acacetin. Thus, the extraction yields of 4 kinds of ILs methanol solution were higher than that of MeOH.

Fig. 1
figure 1

Effect of the type of ionic liquid. Extraction process was performed in an ultrasound unit with a power of 100 W and the concentration of each ILs methanol solution was 0.8 mol/L. 50 mg of the A. rugosa powder of passing through 50-mesh sieve, solid–liquid ratio 1:20 (g/mL), ultrasonic for 30 min. The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

Four different types of ILs had different effects on the extraction yields of tilianin and acacetin. The types of ILs could influence the extraction yield of target analytes. The ion type and alkyl chain length had an effect on the extraction yields of alkaloids [10]. In this experiment, the effect of type of the IL on extraction yields of flavonoids was not investigated because of the limited types of ILs. Thus, the effect of the type on the extraction rate of flavonoids should be investigated in the subsequent work.

Effect of concentrations of the ILs selected

Different concentrations of IL had effect on extraction yields of two target analytes. In order to find out the optimal ionic liquid concentration for two target analytes in A. rugosa, different concentrations ranging from 0.1 to 1 M of [BMIM]Br-methanol solution were investigated while the other conditions were unchanged. The results were shown in Fig. 2 from which, it can be seen that the extraction yields of the target compounds were gradually increased when the concentration of IL was increased from 0.1 to 0.8 M. With the increase in concentration of IL from 0.1 to 0.8 M, the interactions among IL and A. rugosa matrix and cellulose were enhanced, while the dissolution rates of tilianin and acacetin in A. rugosa were accelerated and the extraction yields were improved. While in 1.0 M, the extraction yield was decreased sharply. This might be related to the higher viscosity of ILs. The viscosity of IL was much higher than those of water and conventional organic solvent, thus, the mass transfer resistance was larger than that of traditional extracting agent [7]. The high viscosity of the solvent at high concentrations (1.0 M) of IL could lead to poor infiltration of the solvent into the plant tissue and the decreased extraction yields of two target analytes. Based on these results, 0.8 M [BMIM]Br was finally selected for the following experiments.

Fig. 2
figure 2

Effect of concentration of the ionic liquid selected. Effect of ionic liquid concentration on the extraction yields of two target analytes, with A. rugosa powder of passing through 50-mesh sieve, solid–liquid ratio 1:20 (g/mL), ultrasonic for 30 min. The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

Effect of size of mesh sieves through which A. rugosa was passed

It is well known that the size of the crushed particles influences the extraction yield in the process of natural medicine extraction. According to the above experimental methods, the impact of mesh sieves on extraction yield was investigated with 0.8 M [BMIM]Br IL-methanol solution while the other conditions were unchanged.

The results in Fig. 3 showed that the extraction yields of two target analytes became higher and higher when the sizes of particles were smaller and smaller. According to the optimal comminution granularity of TCM [25], the crushing granularity of A. rugosa should be from 1 to 4 mm. When the particles were too small, it was hard to filter them. Putting all together, the extraction efficiency of the A. rugosa that was passed through 10-mesh sieve to 90-mesh sieve was investigated, and the 90-mesh sieve was ultimately chosen as the optimal condition.

Fig. 3
figure 3

Effect of mesh sieve that A. rugosa passing through. Effect of mesh sieve that A. rugosa passing through on the extraction yield of two target analytes, with 0.8 mol/L [BMIM]Br, solid–liquid ratio 1:20 (g/mL), ultrasonic for 30 min. The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

During the process of crushing sample, we found that the crude stem parts of A. rugosa had a higher degree of lignification and were hard to shatter while the parts of tender stem and leaves were easily crushed. Thus, with the increase in mesh number, the particles of A. rugosa became smaller and smaller and contained more tender stem and leaf parts. It could be inferred that the contents of tilianin and acacetin in the different parts of A. rugosa would be quite different.

In classical prescription on TCM, the stem of A. rugosa was mostly used to treat diseases of stomach and intestines. However, from the other reports [46, 18], we know that tilianin and acacetin didn’t have any activity in these parts. Thus, if we want to clarify the application aspects, we need to reduce the dosage and increase efficacy of drugs. Thus, a lot of work still needs to be continued. The main chemical constituents of different parts of A. rugosa need to be identified and the effects of different parts need to be examined in the subsequent work. The contents of active ingredients in A. rugosa in different parts need to be identified as well.

Effect of ultrasonic time

In this study, we observed that ultrasonic time was another leading factor influencing the extraction efficiencies to certain extend. Figure 4 illustrated that the extraction efficiencies of two target analytes were increased with extending the ultrasonic time from 10 to 30 min, but when ultrasonic time reached 40 min, the extraction efficiency were decreased. Thus, ultrasonic time for 30 min was set for further optimization experiments.

Fig. 4
figure 4

Effect of ultrasonic time. Effect of ultrasonic time on the extraction yield of two target analytes, with A. rugosa powder of passing through 90-mesh sieve, 0.8 M [BMIM]Br, solid–liquid ratio 1:20 (g/mL). The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

The results showed that the extraction yields of the two target analytes were increased with prolonging the ultrasonic time from 10 to 30 min. To extract tilianin and acacetin from the cellular compartments, the solvent must have access to the cellular compartments where the tilianin and acacetin are located. An intact cellular structure restricts accessibility of the solvent to the tilianin and acacetin while ultrasound treated-cells had a more open, fragmented structure, which can facilitate an efficient extraction [22]. The extraction yield reached the maximum when the ultrasonic time was increased to 30 min, while the extraction yield was decreased when the ultrasonic time continued to increase. This may be due to the reason that with the increase of ultrasonic time, some carbohydrate and protein in A. rugosa were extracted, the viscosity of the solution is increased and thus, tilianin and acacetin are adsorbed on solid substrate and not easy to be extracted and thus, the extraction yield was decreased [26]. Because of this reason, the ultrasonic time for 30 min was chosen as the optimal condition in this experiment.

Effect of solid–liquid ratio

To some extent, the solid–liquid ratio was an important parameter, which should be studied to increase the extraction efficiency of two target analytes. On the basis of the above optimized conditions, the effect of solid–liquid ratios on the extraction yield of target extract was investigated. The results were shown in Fig. 5. In Fig. 5, when the solid–liquid ratio was 1:100, the extraction yield reached a maximum. While when the ratio of solid–liquid continued to increase, the extraction yield tended to decline. The dissolution rates of tilianin and acacetin had reached the maximum values at the solid–liquid ratio of 1:100. When the ratio of liquid–solid was further increased, the extraction yield was decreased with the influence of the IL’s properties.

Fig. 5
figure 5

Effect of solid–liquid ratio. Effect of solid–liquid ratio on the extraction yield of two target analytes, with A. rugosa powder of passing through 90-mesh sieve, 0.8 M [BMIM]Br, ultrasonic for 30 min. The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

Figure 5 illustrated that when the ratio of solid–liquid was increased from 1:10 to 1:20, the extraction yield was increased sharply. While when the ratio of liquid–solid was increased from 1:20 to 1:100, the extraction yield was increased slowly. Superfluously, higher solid–liquid ratio could cause procedures more complex and the unnecessary waste, while lower ones would make the extraction of targets incomplete and thus, extraction efficiency lower. Therefore, in the large-scale production of industrialization, the ratio of solid–liquid in the range of 1:20 to 1:100 could be selected to save resources. But in this experiment, 1:100 was chosen for the ratio of solid–liquid, because the test was carried out under the optimal conditions.

Comparison of ILUAE approach with the traditional methods

For the solvent extraction frequently used to extract active ingredient from the TCMs, the solvents included pure water and ethanol with different concentrations. Water was the most frequently used as solvent in clinical application of TCMs. In this study, water, 70% ethanol (EtOH) and methanol (MeOH) were used to extract tilianin and acacetin. In Fig. 6, the IL had a higher extraction yield than did the other two methods. Figure 6 illustrated that the proposed approach obviously increased the extraction yield, indicating that the [BMIM]Br solution is an excellent extractant and that ILUAE is a more rapid and effective sample preparation method.

Fig. 6
figure 6

Effect of solvents on the extraction. Effect of the type of solvents on the extraction yield of two target analytes, with A. rugosa powder of passing through 50-mesh sieve, 0.8 M [BMIM]Br, solid–liquid ratio 1:20 (g/mL), ultrasonic for 30 min. The extraction yield was expressed as the observed values of target analytes (mg/g), the content of tilianin and acacetin per gram of A. rugosa powder

Figure 6 showed that the yields of using water to extract tilianin and acacetin were very low. While the water decoction of A. rugosa is always used in clinic, it was speculated that tilianin and acacetin were not the active components in the traditional application. Nevertheless, tilianin and acacetin possess many biological activities but these activities couldn’t find in A. rugosa. Interestingly, through our study, we found that tilianin and acacetin had a significant anticoagulant activity, while the 70% EtOH extract of A. rugosa didn’t have this activity. Thus, further research is needed to find out the relation between A. rugosa and its main components.

Verification tests

Determination of sample

Under the optimal conditions, the powder of A. rugosa was passed through 90-mesh sieve, and extracted with 1 mL of 0.8 M [BMIM]Br in 1:100 of solid–liquid, after 30 min of ultrasonic-aided extraction, extraction solution was obtained. The concentrations of tilianin and acacetin in sample solution were measured to be 0.0093 and 0.0529 mg/mL, respectively.

Precision experiment

The standard sample solution was determined 6 times according to the above chromatographic conditions. The results showed that the precision of the instrument was good with calculated relative standard deviation (RSDs) values of 0.12 and 0.08%, respectively.

Repeatability

HPLC chromatograms of the standards solution and sample (under the optimal conditions) are shown in Fig. 7. To determine the repeatability of the novel extraction method, six samples of the same weight (10 mg) were processed under the optimum extraction conditions. The mean extraction efficiencies of tilianin and acacetin obtained under the optimized conditions showed good repeatability with calculated RSD values of 4.02 and 3.90%, respectively. These results indicate that the proposed ultrasound-assisted extraction method has an acceptable level of repeatability.

Fig. 7
figure 7

The comparison of sample with standard sample

The results suggest that tilianin and acacetin are stable in the ionic liquid solution during the extraction process. Validation studies on these methods indicate that the proposed method is credible.

Stability

The stability of the target analytes under the experimentally derived optimum conditions was assessed by subjecting standards of tilianin (0.0476 mg/mL) and acacetin (0.0468 mg/mL). The recoveries of the target analytes were assumed to be indicative of the stability of the target analytes under the extraction conditions used.

Under the operating extraction conditions, the contents of tilianin and acacetin varied from 100 to 101.8% and from 100 to 100.6%, respectively, within 24 h. The structures of target analytes were stable, with no change in retention time. Therefore the structural change was not significant under the selected optimum conditions.

Recovery

Under the optimized conditions detailed above, two samples spiked with tilianin and acacetin were extracted and the recoveries of tilianin and acacetin from dried A. rugosa were 96.9 and 97.9%, respectively.

Conclusions

In this study, an efficient method was developed for the extraction of tilianin and acacetin from A. rugosa. The optimum conditions for ILUAE were determined. Compared with traditional methods, the present approach obtained higher extraction yields of tilianin and acacetin, which were 2 to 202 times and 3 to 14 times of those of traditional methods, respectively. This study also demonstrated that the IL solution was an excellent extractant and that ILUAE was a simple, rapid, and effective extraction method. Moreover, with the unique characteristics of IL, the proposed approach in this study had the environmentally friendly, convenient, efficient characteristics and could be the high practical value technique in sample preparation and analysis. Thus, this experiment in combination with the related reports indicates that the extraction of active ingredients in TCM by ionic liquid is a breakthrough one. It provides a theoretical basis for the healthy and sustainable development of TCM resources.

Abbreviations

ILUAE:

ionic liquid based ultrasonic-assisted extraction

TCM:

traditional Chinese medicine

HPLC:

high-performance liquid chromatography

IL:

ionic liquid

ILs:

ionic liquids

UAE:

ultrasonic-assisted

[HMIM]PF6 :

1-hexyl-3-methylimidazolium hexafluorophosphate

[BMIM]BF4 :

1-butyl-3-methyl imidazolium tetrafluoroborate

[BMIM]Br:

1-butyl-3-methyl imidazole bromide

[BMIM]PF6 :

1-butyl-3- methylimidazolium hexafluorophosphate

LOD:

the limit of detection

LOQ:

the limit of quantification

EtOH:

ethanol

MeOH:

methanol

RSD:

relative standard deviation

SD:

standard deviation

References

  1. Wang KC, Chang JS, Chiang LC, Lin CC (2009) 4-Methoxycinnamaldehyde inhibited human respiratory syncytial virus in a human larynx carcinoma cell line. Phytomedicine. 16:882–886 (View Article)

    Article  CAS  Google Scholar 

  2. Shin S (2004) Essential oil compounds from Agastache rugosa as antifungal agent against Trichophyton species. Arch Pharm Res. 27:295–299 View Article

    Article  CAS  Google Scholar 

  3. Guo KJ, Xu SF, Yin P, Wang W, Song XZ, Liu FH et al (2011) Active components of common traditional Chinese medicine decoctions have antioxidant functions. J Anim Sci. 89:3107–3115 View Article

    Article  CAS  Google Scholar 

  4. Hernandez-Abreu O, Torres-Piedra M, Garcia-Jimenez S, Ibarra-Barajas M, Villalobos-Molina R, Montes S et al (2013) Dose-dependent antihypertensive determination and toxicological studies of tilianin isolated from Agastache mexicana. J Ethnopharmacol. 146:187–191 View Article

    Article  CAS  Google Scholar 

  5. Nam KW, Kim J, Hong JJ, Choi JH, Woonchon M, Cho MH et al (2005) Inhibition of cytokine-induced IkappaB kinase activation as a mechanism contributing to the anti-atherogenic activity of tilianin in hyperlipidemic mice. Atherosclerosis 180:27–35

    Article  CAS  Google Scholar 

  6. Zielińska S, Matkowski A (2014) Phytochemistry and bioactivity of aromatic and medicinal plants from the genus Agastache (Lamiaceae). Phytochem Rev 13:391–416 View Article

    Article  Google Scholar 

  7. Shao JJ, Wu H, Zhao YQ, Duan JA (2013) Ionic liquid extraction technology and its application in field of Chinese material medica. Chinese Tradit Herbal Drugs. 44:3561–3565 View Article

    CAS  Google Scholar 

  8. Goharshadi EK, Moosavi M (2008) Thermodynamic properties of some ionic liquids using a simple equation of state. J Mol Liq. 142:41–44 View Article

    Article  CAS  Google Scholar 

  9. Aerov AA, Khokhlov AR, Potemkin II (2006) Why ionic liquids can possess extra solvent power. J Phys Chem B. 110:16205–16207 View Article

    Article  CAS  Google Scholar 

  10. Ma WY, Lu YB, Hu RL, Chen JH, Zhang ZZ, Pan YJ (2010) Application of ionic liquids based microwave-assisted extraction of three alkaloids N-nornuciferine, O-nornuciferine, and nuciferine from lotus leaf. Talanta. 80:1292–1297 View Article

    Article  CAS  Google Scholar 

  11. Xu DP, Zhou Y, Zheng J, Li S, Li AN, Li HB (2016) Optimization of ultrasound-assisted extraction of natural antioxidants from the flower of Jatropha integerrima by response surface methodology. Molecules. 21:1–12 View Article

    Google Scholar 

  12. Hamdaoui O, Naffrechoux E (2007) An investigation of the mechanisms of ultrasonically enhanced desorption. AICHE J. 53:363–373 View Article

    Article  CAS  Google Scholar 

  13. Majd MH, Rajaei A, Bashi DS, Mortazavi SA, Bolourian S (2014) Optimization of ultrasonic-assisted extraction of phenolic compounds from bovine pennyroyal (Phlomidoschema parviflorum) leaves using response surface methodology. Ind Crop Prod. 57:195–202 View Article

    Article  Google Scholar 

  14. Vuong QV, Thanh DT, Bhuyan DJ, Goldsmith CD, Sadeqzadeh E, Scarlett CJ et al (2015) Optimization of ultrasound-assisted extraction conditions for euphol from the medicinal plant, Euphorbia tirucalli, using response surface methodology. Ind Crop Prod. 63:197–202 View Article

    Article  CAS  Google Scholar 

  15. Ma Y, Ye X, Hao Y, Xu G, Xu G, Liu D (2008) Ultrasound-assisted extraction of hesperidin from Penggan (Citrus reticulata) peel. Ultrason Sonochem. 15:227–232 View Article

    Article  CAS  Google Scholar 

  16. Vilkhu K, Mawson R, Simons L, Bates D (2008) Applications and opportunities for ultrasound assisted extraction in the food industry—a review. Innov Food Sci Emerg Technol. 9:161–169 View Article

    Article  CAS  Google Scholar 

  17. Zheng LL, Wen G, Yuan MY, Gao F (2016) Ultrasound-assisted extraction of total flavonoids from corn silk and their antioxidant activity. J Chem. 2016:1–5 View Article

    Google Scholar 

  18. Zhou YY, Zhong BH, Shi WG (2014) Progress in research of acacetin biologic properties. Chinese J New Drugs. 23:1053–1056 View Article

    CAS  Google Scholar 

  19. Xie LF, Liu YP, Wang X, Xin D (2014) Simultaneous determination of the contents of chlorogenic acid, linarin and acacetin in Cirsiumsetosum by RP-HPLC. J Shenyang Pharm Univ. 31:451–454 View Article

    CAS  Google Scholar 

  20. Yu N, Chen W, Xing JG, He CH, Liu GH (2015) HPLC determination of four components in YixinBadiranjibuya granules. Chin J Pharm Anal. 35:670–674 View Article

    CAS  Google Scholar 

  21. Wang YJ, Wang LM, Yang S, Ren DM (2011) Simultaneous determination of tilianin and agastachoside in Dracocephalum moldavica by HPLC. Chinese Tradit Herbal Drugs. 42:91–93 View Article

    Google Scholar 

  22. Lei Y, Li LL, Liu TT, Zu YG, Yang FJ, Zhao CJ et al (2013) Development of sample preparation method for isoliquiritigenin, liquiritin, and glycyrrhizic acid analysis in licorice by ionic liquids-ultrasound based extraction and high-performance liquid chromatography detection. Food Chem. 138:173–179 View Article

    Article  Google Scholar 

  23. Ha SH, Mai NL, An G, Koo YM (2011) Microwave-assisted pretreatment of cellulose in ionic liquid for accelerated enzymatic hydrolysis. Bioresour Technol. 102:1214–1219 View Article

    Article  CAS  Google Scholar 

  24. Jin HR, Ling F, Xiao N (2011) Ionic Liquid-Assisted extraction of paeonol from Cynanchum paniculatum. Chromatographia. 73:787–792 View Article

    Article  CAS  Google Scholar 

  25. Huang K, Shu ZH, Liu GF (2005) Research progress on the particle size of traditional Chinese Medicine. Chinese J Info TCM. 12:97–98 View Article

    Google Scholar 

  26. Fan JP, Cao J, Kong T, Zhang L (2011) Optimization of ultrasonic-assisted [Bmim]Br-K2HPO4 aqueous two-phase system extraction of puerarin from Pueraria. J Chem Eng Chinese Univ. 25:955–960

    CAS  Google Scholar 

Download references

Authors’ contributions

WYK and JFW conceived the research idea. PRC and JMW conducted the experiments, collected the plant specimens, analyzed and interpreted the data as well as prepared the first draft. JMW identified the plants. WYK, PRC, and JFW critically read and revised the paper. All authors read and approved the final manuscript.

Acknowledgements

This work was supported by Basic and Advance Project in Science and Technology Agency of Henan Province (142300410123 and 152300410064), National Cooperation Project of Henan province (2015GH12) and Natural Science Project in department of education of Henan Province (16A360008), Kaifeng City Science and Technology Innovation Talent (1509010), Industry Research Project in Science and Technology Agency of Henan Province (162107000038 and 152107000051), Henan Province University Science and Technology Innovation Team (16IRTSTHN019).

Competing interests

The authors declare that they have no competing interests.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Wenyi Kang.

Rights and permissions

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Wei, J., Cao, P., Wang, J. et al. Analysis of tilianin and acacetin in Agastache rugosa by high-performance liquid chromatography with ionic liquids-ultrasound based extraction. Chemistry Central Journal 10, 76 (2016). https://doi.org/10.1186/s13065-016-0223-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1186/s13065-016-0223-7

Keywords